Assuming PC MAIN Internal IP Address is 192.168.1.150

Media Encoder must have port 8080 and 8081 open for streaming. Router Port Should Daisy Chain Internal IP address to External Address.

Encoder on PC 192.168.1.150 port 8080 or 8081, Router NAT Open Port 8080 or 8081 to See IP 192.168.1.150 from outside internet to Public IP Address (whatismyip.com)

START-CONTROL PANEL-NETWORK CONNECTIONS-LAN- Right Click Properties-TCP/IP Properties – Check the following information.

Ok-Ok- Enable or Disable, Enable then

More Technical Settings -

admin is the admin password for the linksys router

192.168.1.1 is the gateway

For a dedicated PC you should really use a static IP address so that IP addresses will not have to be manually updated with each broadcast. That will eliminate going through this everytime you broadcast.

Here are the Linksys Static IP for the Broadcast PC – Note: Whatever address you choose must have an associated firewall rule setup in the router.

Firewall port rule for Stream

DMZ

After connecting the router, open a Web Browser (Such as Internet Explorer or Netscape)
When the browser opens, go to the "Address" bar and input the Routers IP Address (The Routers default IP Address is 192.168.1.1) then click on the Go button or hit the [Enter] key.
A window will pop up prompting for a "User Name" and "Password", leave the "User Name" blank and input the Routers password (admin is the routers default Password) then click on the OK button.
After inputting the Password, the "Setup" page should appear.
When the "Setup" page appears, click on the Applications & Gaming tab.
The "Port Range Forwarding" area should appear, click on the DMZ sub tab and fill in the following information:
- DMZ: Set this option to Enable when DMZ is being used.
- DMZ Host IP Address: This field needs the IP Address of the computer that is being placed in to the DMZ. For example if the computer that needed to be in DMZ, and it had an IP address of 192.168.1.150, then we would input 8081 into the "DMZ Host IP Address" field.
Click on the Save Settings button when all of the information has been input, and click on the Continue button when prompted, after doing this DMZ will be Setup.

General Setup Settings

This picture assumes the Broadcast PC’s IP Address is 192.168.1.150

The Gateway or Router is 192.168.1.1

Setting DMZ and NAT or Port Forwarding

In our case we setup a bcast application and make the port 8080 or 8081 and assign the Internal IP address of the broadcast – machine. One fast way that is less secure is to setup a DMZ – This will allow all access to the PC while maintaining the firewall settings for other machines.

These values are assuming that a Linksys router is being used with a LAN IP Address of 192.168.1.1, if not please make the appropriate changes to match the network being used.

Click on the Start menu and click on the Run option.
When the "Run" window opens, input control ncpa.cpl into the "Open" field then click on the OK button.
The "Network Connections" window will open, right click on the Local Area Connection icon and click on the Properties option.
When the "Local Area Connection Properties" window appears, select Internet Protocol TCP/IP then click on the Properties button.
Change option from Obtain Automatically to Use the following and input:
- IP: 192.168.1.150(If multiple static IP's are going to be used, the next computer would be .25, and next would be .30, etc)
- Subnet Mask: 255.255.255.0
- Default Gateway: 192.168.1.1
- Primary DNS: 192.168.1.1
Click OK then Close

More Settings

After connecting the router, open a Web Browser (Such as Internet Explorer or Netscape)
When the browser opens, go to the "Address" bar and input the Routers IP Address (The Routers default IP Address is 192.168.1.1) then click on the Go button or hit the [Enter] key.
A window will pop up prompting for a "User Name" and "Password", leave the "User Name" blank and input the Routers password (admin is the routers default Password) then click on the OK button.
After inputting the Password, the "Setup" page should appear.
When the "Setup" page appears, click on the Applications & Gaming tab.
The "Port Range Forwarding" area should appear, fill in the following information:

In this example, the server that is being used is an FTP server, and the ports that would need to be opened are ports 8081 and 8080:
- Application: This will be the name of the Application that needs to have the ports open. This is for reference only, it does not control the Port Forwarding. For the sake of this example, we would input BCAST in the "Application" field.
- Start: This will be the first port in a range of ports. Since we want ports 8080 or 8081 to be open even though we only need one port open we can assign a range, we will input 8080 into the "Start" field.
- End: This would be the last port in the range of ports to be forwarded*. Since BCAST will use ports 8080-8081 to be open, we will input 8081 into the "End" field.*
- Protocol: This field indicates which protocol that the application uses (either UDP or TCP), if unsure, leave the field set to Both.
- IP Address: This field needs the IP Address of the computer that the ports are being forwarded too. For example if the computer that needed the ports forwarded to it had an IP address of 192.168.1.150, then we would input 8081 into the "IP Address" field.
- Enabled: This box should be checked when the Application is being used, if for some reason it should need to be disabled, uncheck the box and the Router will stop Forwarding the ports to that computer.
Click on the Save Settings button when all of the information has been input, and click on the Continue button when prompted, after doing this the Ports will be Forwarded.

After connecting the router, open a Web Browser (Such as Internet Explorer or Netscape)

When the browser opens, go to the "Address" bar and input the Routers IP Address (The Routers default IP Address is 192.168.1.1) then click on the Go button or hit the [Enter] key.

A window will pop up prompting for a "User Name" and "Password", leave the "User Name" blank and input the Routers password (admin is the routers default Password) then click on the OK button.

After inputting the Password, the "Setup" page should appear.

When the "Setup" page appears, click on the Applications & Gaming tab.

The "Port Range Forwarding" area should appear, click on the DMZ sub tab and fill in the following information:

DMZ: Set this option to Enable when DMZ is being used.

DMZ Host IP Address: This field needs the IP Address of the computer that is being placed in to the DMZ. For example if the computer that needed to be in DMZ, and it had an IP address of 192.168.1.150, then we would input 8081 into the "DMZ Host IP Address" field.

Click on the Save Settings button when all of the information has been input, and click on the Continue button when prompted, after doing this DMZ will be Setup.

These values are assuming that a Linksys router is being used with a LAN IP Address of 192.168.1.1, if not please make the appropriate changes to match the network being used.

Click on the Start menu and click on the Run option.

When the "Run" window opens, input control ncpa.cpl into the "Open" field then click on the OK button.

The "Network Connections" window will open, right click on the Local Area Connection icon and click on the Properties option.

When the "Local Area Connection Properties" window appears, select Internet Protocol TCP/IP then click on the Properties button.

Change option from Obtain Automatically to Use the following and input:

IP: 192.168.1.150(If multiple static IP's are going to be used, the next computer would be .25, and next would be .30, etc)

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

Primary DNS: 192.168.1.1

Click OK then Close

After connecting the router, open a Web Browser (Such as Internet Explorer or Netscape)

When the browser opens, go to the "Address" bar and input the Routers IP Address (The Routers default IP Address is 192.168.1.1) then click on the Go button or hit the [Enter] key.

A window will pop up prompting for a "User Name" and "Password", leave the "User Name" blank and input the Routers password (admin is the routers default Password) then click on the OK button.

After inputting the Password, the "Setup" page should appear.

When the "Setup" page appears, click on the Applications & Gaming tab.

The "Port Range Forwarding" area should appear, fill in the following information:

In this example, the server that is being used is an FTP server, and the ports that would need to be opened are ports 8081 and 8080:

Application: This will be the name of the Application that needs to have the ports open. This is for reference only, it does not control the Port Forwarding. For the sake of this example, we would input BCAST in the "Application" field.

Start: This will be the first port in a range of ports. Since we want ports 8080 or 8081 to be open even though we only need one port open we can assign a range, we will input 8080 into the "Start" field.

End: This would be the last port in the range of ports to be forwarded. Since BCAST will use ports 8080-8081 to be open, we will input 8081 into the "End" field.

Protocol: This field indicates which protocol that the application uses (either UDP or TCP), if unsure, leave the field set to Both.

IP Address: This field needs the IP Address of the computer that the ports are being forwarded too. For example if the computer that needed the ports forwarded to it had an IP address of 192.168.1.150, then we would input 8081 into the "IP Address" field.

Enabled: This box should be checked when the Application is being used, if for some reason it should need to be disabled, uncheck the box and the Router will stop Forwarding the ports to that computer.

Click on the Save Settings button when all of the information has been input, and click on the Continue button when prompted, after doing this the Ports will be Forwarded.

After connecting the router, open a Web Browser (Such as Internet Explorer or Netscape)

When the browser opens, go to the "Address" bar and input the Routers IP Address (The Routers default IP Address is 192.168.1.1) then click on the Go button or hit the [Enter] key.

A window will pop up prompting for a "User Name" and "Password", leave the "User Name" blank and input the Routers password (admin is the routers default Password) then click on the OK button.

After inputting the Password, the "Setup" page should appear.

When the "Setup" page appears, click on the Applications & Gaming tab.

The "Port Range Forwarding" area should appear, click on the DMZ sub tab and fill in the following information:

DMZ: Set this option to Enable when DMZ is being used.

DMZ Host IP Address: This field needs the IP Address of the computer that is being placed in to the DMZ. For example if the computer that needed to be in DMZ, and it had an IP address of 192.168.1.150, then we would input 8081 into the "DMZ Host IP Address" field.

Click on the Save Settings button when all of the information has been input, and click on the Continue button when prompted, after doing this DMZ will be Setup.

These values are assuming that a Linksys router is being used with a LAN IP Address of 192.168.1.1, if not please make the appropriate changes to match the network being used.

Click on the Start menu and click on the Run option.

When the "Run" window opens, input control ncpa.cpl into the "Open" field then click on the OK button.

The "Network Connections" window will open, right click on the Local Area Connection icon and click on the Properties option.

When the "Local Area Connection Properties" window appears, select Internet Protocol TCP/IP then click on the Properties button.

Change option from Obtain Automatically to Use the following and input:

IP: 192.168.1.150(If multiple static IP's are going to be used, the next computer would be .25, and next would be .30, etc)

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

Primary DNS: 192.168.1.1

Click OK then Close

After connecting the router, open a Web Browser (Such as Internet Explorer or Netscape)

When the browser opens, go to the "Address" bar and input the Routers IP Address (The Routers default IP Address is 192.168.1.1) then click on the Go button or hit the [Enter] key.

A window will pop up prompting for a "User Name" and "Password", leave the "User Name" blank and input the Routers password (admin is the routers default Password) then click on the OK button.

After inputting the Password, the "Setup" page should appear.

When the "Setup" page appears, click on the Applications & Gaming tab.

The "Port Range Forwarding" area should appear, fill in the following information: In this example, the server that is being used is an FTP server, and the ports that would need to be opened are ports 8081 and 8080:

Application: This will be the name of the Application that needs to have the ports open. This is for reference only, it does not control the Port Forwarding. For the sake of this example, we would input BCAST in the "Application" field.

Start: This will be the first port in a range of ports. Since we want ports 8080 or 8081 to be open even though we only need one port open we can assign a range, we will input 8080 into the "Start" field.

End: This would be the last port in the range of ports to be forwarded*. Since BCAST will use ports 8080-8081 to be open, we will input 8081 into the "End" field.*

Protocol: This field indicates which protocol that the application uses (either UDP or TCP), if unsure, leave the field set to Both.

IP Address: This field needs the IP Address of the computer that the ports are being forwarded too. For example if the computer that needed the ports forwarded to it had an IP address of 192.168.1.150, then we would input 8081 into the "IP Address" field.

Enabled: This box should be checked when the Application is being used, if for some reason it should need to be disabled, uncheck the box and the Router will stop Forwarding the ports to that computer.

Click on the Save Settings button when all of the information has been input, and click on the Continue button when prompted, after doing this the Ports will be Forwarded.

The "Port Range Forwarding" area should appear, fill in the following information:

In this example, the server that is being used is an FTP server, and the ports that would need to be opened are ports 8081 and 8080:

End: This would be the last port in the range of ports to be forwarded. Since BCAST will use ports 8080-8081 to be open, we will input 8081 into the "End" field.